Altech-auto-security 5BCR10P Bedienungsanleitung PDF herunterladen

128-8776

1 of 8

Your Alarm and or Remote Start unit has a configurable receiver that allows

the transmitter to be programmed to operate the Lock Unlock functions with

one transmitter button or with two transmitter buttons (separate Lock/

Unlock). In addition, the receiver also allows driver priority function. This

driver priority function takes place when ever a particular transmitter is

used to unlock the vehicle regardless of the selection of one button or two

button operation.

The following indicates the receiver programmable slots.

1 Lock/Unlock or Lock

2 Unlock if Programmed

3 Trunk Release & or Remote Start (Optional on some models)

4 Auxiliary Output

5 Auxiliary Output

6 Driver 1 Priority or Sperate Output

7 Driver 2 Priority or Separate Output

Receiver channels 6 or 7 will accept the programming of transmitter

channel 1 if used as the Lock/Unlock button, or Channel 2 when separate

Lock Unlock buttons are programmed. In this way, whenever the transmit-

ter is used to unlock the vehicle, channel 6 or 7, when programmed, will

provide a pulsed ground output. This output can be connected to the driver

priority function of the vehicle to reset preset user features. Please consult

with your installation center technician to see if this feature is available in

your vehicle.

NOTE: A total of 4 transmitters may be programmed into any receiver

channel.

Force programming a transmitter, removing a transmitter, or reprioritizing a

transmitter is covered later in this manual.

Also, if you do not program a transmitter button into channel 2 which is the

separate unlock/disarm channel, then whatever button is programmed into

channel 1 will serve as both lock/arm & unlock/disarm.

NOTE: The RED Button serves as a function button in combination with other

buttons explained in your owners manual. This button may not be used to

operate a receiver channel.

NOTE: The Option Button is predetermined and programmed for access to

Time Start, and Temperature Start & Check so it cannot be used for multiple

button operation of any other feature. It will however operate for any single

button programming.

This transmitter is also capable of one button programming for certain model

Audiovox Alarms. If your alarm is one of these models, then when step 3 is

completed on the following page, you can turn the ignition switch off and

Model 5BCR10P

Programming Guide

1 2 3 4 5 6 7 8

Model 5BCR10P 1
128-8776 2

Inhaltsverzeichnis

Seite 1 - Model 5BCR10P

128-87761 of 8Your Alarm and or Remote Start unit has a configurable receiver that allowsthe transmitter to be programmed to operate the Lock Unlock

Seite 2 - 128-8776

128-87762 of 82THIS PAGE LEFT BLANK INTENTIONALLY

Seite 3

128-87763 of 8programming with the default button configurations for the first four chan-nels will be complete.TO ENTER THE PROGRAM MODE:1. Turn the i

Seite 4

128-87764 of 811. Within 10 Seconds, press and hold any unused button(s) of the firsttransmitter you wish to control Channel 5 output, (Auxiliary Outp

Seite 5

128-87765 of 83 slots. If in step 3 you identified two transmitters, you will have to fill theadditional two slots, etc...4. Press and hold any unuse

Seite 6

128-87766 of 8To replace the transmitter battery:1. Slightly lift the battery cover where shown and slide in the direction notedon the cover.2. Remove

Seite 7

128-87767 of 8Attention: Transmitter Ordering DepartmentImportant: To help us expedite your order, please print all of the informationlegibly and mai

Seite 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Altech-auto-security 5BCR10P Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Altech-auto-security 5BCR10P herunter. Altech Auto Security 5BCR10P User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern